Tippmann Pneumatics Inc. Homepage
  FAQ FAQ  Forum Search   Register Register  Login Login

3D Manual (98 and A5 so far)

 Post Reply Post Reply Page  <1234>
Author
e-gripA-5er View Drop Down
Member
Member
Avatar

Joined: 06 February 2005
Location: United States
Status: Offline
Points: 27
Post Options Post Options   Thanks (0) Thanks(0)   Quote e-gripA-5er Quote  Post ReplyReply Direct Link To This Post Posted: 07 March 2005 at 9:55pm

Originally posted by SpoonSports808 SpoonSports808 wrote:

Hi I think I lost my Drive Spring GUide Pin! Anyone know any alternative to it? HAs anyone lost it before what did u do?

umm just go to  http://www.paintball-discounters.com/cgi-bin/webc.cgi/st_mai n.html?p_catid=259&sid=5bW2dL1EcHZr8R6-40105263018.b8  and then to A-5 parts and they have every part of the A-5 for sale

Back to Top
fastrigger81 View Drop Down
Member
Member
Avatar

Joined: 06 March 2005
Location: United States
Status: Offline
Points: 98
Post Options Post Options   Thanks (0) Thanks(0)   Quote fastrigger81 Quote  Post ReplyReply Direct Link To This Post Posted: 29 March 2005 at 6:43pm
can someone show me a pic of the 98custom w/o the rt and one wiht the rt? it would REALLY HELP
Tippmann 98 custom
12 inch JJ Pro 1 Barrel
Dead on drop foward
expansion chamber
pen spring mod
12v Revvy w/ x board
Dead on 2x Trigger
Back to Top
tippmannlad View Drop Down
Member
Member


Joined: 22 March 2005
Location: United States
Status: Offline
Points: 46
Post Options Post Options   Thanks (0) Thanks(0)   Quote tippmannlad Quote  Post ReplyReply Direct Link To This Post Posted: 09 June 2005 at 6:37pm

heres a picture with a response trigger right of tippmanns web site 

if you want somthing done right do it yourself

98 custom-$135(used)
Eggy 2-$30(used
camo 4+1 pack-$10(used)
20oz co2-(came with gun)
jumping on friend out of a tree during game-PRICELESS


Back to Top
Baratak View Drop Down
Gold Member
Gold Member
Avatar
Technical Wunderkind

Joined: 19 November 2002
Location: United States
Status: Offline
Points: 1611
Post Options Post Options   Thanks (0) Thanks(0)   Quote Baratak Quote  Post ReplyReply Direct Link To This Post Posted: 30 June 2005 at 11:33pm
Hey guys, someone should have PMed me about the broken A-5 link, Yahoo freaked out... I'll see if I can dig up my local copy for you and repost...
Everyone dies, not everyone truly lives.

MySpace

Back to Top
lalaland View Drop Down
Member
Member


Joined: 23 October 2004
Location: United Kingdom
Status: Offline
Points: 26
Post Options Post Options   Thanks (0) Thanks(0)   Quote lalaland Quote  Post ReplyReply Direct Link To This Post Posted: 05 September 2005 at 1:57pm
Originally posted by Baratak Baratak wrote:

Hey guys, someone should have PMed me about the broken A-5 link, Yahoo freaked out... I'll see if I can dig up my local copy for you and repost...
Hi,

If you find your local copy and need it hosting give me a shout. I have plenty of space on a paid host and can spare some bandwith for fellow Tippmann users.

I am really keen to see it too as I am attempting to take my A5 apart for the first time tonight before a game on Sunday and as parts and service are near impossible to find here in the UK for Tippmann markers it's a bit of a nervous activity for me.
Back to Top
vonfeldt7 View Drop Down
Member
Member
Avatar

Joined: 05 November 2004
Location: United States
Status: Offline
Points: 345
Post Options Post Options   Thanks (0) Thanks(0)   Quote vonfeldt7 Quote  Post ReplyReply Direct Link To This Post Posted: 10 November 2005 at 10:39pm
if you want a website...its on teh bottom of my sig...i made it a few days ago.. its better then clicking a link 4 every pic.
novice paintball help(If you own a tippy and your new to paintball, this site may help)
Jesus is my friend
DO NOT say"sniper"here!
Back to Top
Baratak View Drop Down
Gold Member
Gold Member
Avatar
Technical Wunderkind

Joined: 19 November 2002
Location: United States
Status: Offline
Points: 1611
Post Options Post Options   Thanks (0) Thanks(0)   Quote Baratak Quote  Post ReplyReply Direct Link To This Post Posted: 15 January 2006 at 6:11pm
Ok, I'm sorry I vanished... I don't have a local copy of those pictures anymore, but I do have an A-5 and Camera... Who has a spot to host them?

PM me, I'll start taking pictures tonight...

It's modified, but the basics will still be there.
Everyone dies, not everyone truly lives.

MySpace

Back to Top
KALIS-PIMENTA View Drop Down
Member
Member
Avatar
Strike 2 for inflammatory posting 3/3/06

Joined: 19 January 2006
Location: United States
Status: Offline
Points: 342
Post Options Post Options   Thanks (0) Thanks(0)   Quote KALIS-PIMENTA Quote  Post ReplyReply Direct Link To This Post Posted: 12 February 2006 at 2:15pm
I guess he vanished again
Tippmann A-5
Polished internals
Rampage Board
Rampage Pro-E Trigger
TechT A-5Mod
QEV mod
Lapco autococker Adapter
STIFFI Kit
JCS Power Tube
PALMER Stabilizer
LPK
PsychoZ-DF
Ricochet R5
Back to Top
--Red-- View Drop Down
Member
Member
Avatar

Joined: 13 February 2006
Location: United States
Status: Offline
Points: 377
Post Options Post Options   Thanks (0) Thanks(0)   Quote --Red-- Quote  Post ReplyReply Direct Link To This Post Posted: 28 February 2006 at 5:44pm
Baratak how do i pm you, i really need help on the internal diagram pics and stuff like that of A-5
Back to Top
rdcisneros3 View Drop Down
Member
Member


Joined: 03 February 2006
Location: United States
Status: Offline
Points: 226
Post Options Post Options   Thanks (0) Thanks(0)   Quote rdcisneros3 Quote  Post ReplyReply Direct Link To This Post Posted: 09 March 2006 at 1:17pm

Wow, I never realized how easy it could be taking the gun apart. I've never taken the rubber end cap off of the charging handle so I've always removed the rear bolt and drive spring along with the left side receiver. Makes it a real pain to put back together.

Is there a certain way to take the rubber end cap off (i.e. using pliers) or does it just slide off?

Donny Cisneros
Back to Top
Bango View Drop Down
Platinum Member
Platinum Member
Avatar
Rugged Individualist

Joined: 30 January 2004
Location: United States
Status: Offline
Points: 2572
Post Options Post Options   Thanks (0) Thanks(0)   Quote Bango Quote  Post ReplyReply Direct Link To This Post Posted: 19 June 2006 at 6:29pm
A5 Internals




First off, the ball detent. Make sure when you put it in, it's facing the direction mine is.

Valve O-ring. This is located up inside the powertube where the arrow is pointing. It's important that you keep this well oiled or else it will cause the infamous leaking from the barrel.

Front bolt. If you put this in backwards, it will make cocking your gun a lot harder/impossible. Just make sure yours is facing the direction mine is and you'll be good.

Tombstone latch. This keeps your vertical adapter in place. I left mine off once and the vertical adapter slipped out of place and caused a leak, so just make sure it's always latched on to the adapter. I also recommend replacing the stock spring with a lighter clciky pen spring because the stock one makes it hard to unlatch.

Drive spring. Make sure the pin is placed inside it to keep it from bending. You can sort of notice the pin in the first picture.


Edited by Bango - 19 June 2006 at 6:30pm
Back to Top
NeonForFaen View Drop Down
Member
Member
Avatar

Joined: 26 June 2006
Location: Norway
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote NeonForFaen Quote  Post ReplyReply Direct Link To This Post Posted: 26 June 2006 at 8:49am

Originally posted by EYES EYES wrote:

Link to Picture

 

ok i got two of these springs, but their not the same.... the secon spring is longer and it's cut in 2 but still together....

does this bellong in the gun or is it something i found in m room...if it bellongs can someone give me a hint were it should be...

Thnx:D

Back to Top
Crazystick View Drop Down
Member
Member


Joined: 10 July 2006
Location: United States
Status: Offline
Points: 15
Post Options Post Options   Thanks (0) Thanks(0)   Quote Crazystick Quote  Post ReplyReply Direct Link To This Post Posted: 10 July 2006 at 7:34pm
just for reference. What is the PSI that the A-5 should be running at. CO2 vs HPA.. LPK's and what their function is exactly. What about having a regulator on the gun. Besides the one on a HPA tank.
Back to Top
Crazystick View Drop Down
Member
Member


Joined: 10 July 2006
Location: United States
Status: Offline
Points: 15
Post Options Post Options   Thanks (0) Thanks(0)   Quote Crazystick Quote  Post ReplyReply Direct Link To This Post Posted: 18 July 2006 at 12:34am
What about a pic of a RT internals. .  there is a valve with 2 very small o rings..
Where may i find a replacement kit for those? I have my cyclone air system, well just shooting out 1-2 balls . then it jams.. or stops.. so .. i wanna make sure I got all my valve/orings covered before I move on and test other things.
Back to Top
hudboy7 View Drop Down
Member
Member


Joined: 22 March 2007
Location: United States
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote hudboy7 Quote  Post ReplyReply Direct Link To This Post Posted: 22 March 2007 at 7:30pm
hey I have a tipmann 98 custom and recently its been messed up, when i shoot the gun a bunch of co2 goes through it and the whoel gun goes rattatta with co2 burst constantly going out of the barell and the gun instantly becomes cold. I talked with my friend today and he worked me through some of the things that could be the problem. I tried everything it still does the same thing.... can some one please help me?
Back to Top
backupdecoy View Drop Down
Member
Member
Avatar

Joined: 01 April 2007
Location: Canada
Status: Offline
Points: 8
Post Options Post Options   Thanks (0) Thanks(0)   Quote backupdecoy Quote  Post ReplyReply Direct Link To This Post Posted: 03 April 2007 at 4:19pm
Thanks for the pics of the 98 custom trigger, it saved me a lot of time (and money) on getting the proshop put it back together. Helped a lot.
I own you, you own him, he owns her, she owns me.
Back to Top
birdhouse View Drop Down
Member
Member
Avatar

Joined: 15 April 2007
Location: Canada
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote birdhouse Quote  Post ReplyReply Direct Link To This Post Posted: 15 April 2007 at 5:58pm
Hi gang! I'm relatively new to paintball and I just bought (today, April 15th) my first gun from Tippmann, the 98 Custom. However, me being a newbie and all, I assembled it the way was most logic and...it won't shoot. I've played paintball before but I've never owned my own gun. So, I tried reading the owner's manual in detail and followed all instructions. I must be doing something wrong 'cause it just ain't working!  Now, I'll tell you what I've done: I've removed the packaging (duh) took it out, put on the CO2 canister and the paintball cartouche, and...that's about it. Does the canister come with CO2 in it? Do I actually have to put an 8v battery, as specified but the manual, 'cause there isn't any space for one. Anything else I might be doing wrong? If someone owns this exact gun, could they tell me how they got theirs to work? Thanks. (I'm sure it's nothing but a stupid mistake)
Mike
Back to Top
phil_stl View Drop Down
Gold Member
Gold Member
Avatar
strike 1 flaming 3/2

Joined: 01 April 2006
Status: Offline
Points: 1421
Post Options Post Options   Thanks (0) Thanks(0)   Quote phil_stl Quote  Post ReplyReply Direct Link To This Post Posted: 15 April 2007 at 10:09pm
You need CO2 in your CO2 tank.  Go get it filled!!

I don't know what you're talking about with the 8v?  Do you have e-grip in your marker?  Then ya it would probably need a battery.
Back to Top
mblier View Drop Down
Member
Member
Avatar

Joined: 16 April 2007
Location: United States
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote mblier Quote  Post ReplyReply Direct Link To This Post Posted: 16 April 2007 at 4:08pm
Wow warp feeds I haven't seen them in a while.
Owner Of Triple T Paintball
http://www.tttpaintball.net
mike@tttpaintball.net
http://z8.invisionfree.com/Triple_T_Paintball/index.php?s=0e 2e2a03f401b6a
Back to Top
mmon0429 View Drop Down
Member
Member


Joined: 08 January 2008
Location: United States
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote mmon0429 Quote  Post ReplyReply Direct Link To This Post Posted: 08 January 2008 at 7:03pm
hey idk if you still look at this and add to it but uhh was wondering if you could find me a picture of all the o rings inside the 98 cause my gun is leaking CO2 and idk where and which ones to replace
Back to Top
 Post Reply Post Reply Page  <1234>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.03

This page was generated in 0.141 seconds.